Action: Permit (Note: Do not select Tunnel or specify Tunnel VPN because this is a route-based VPN configuration) Position at Top: Enabled; Click OK; Create static route for destination network through VPN: Click Network > Routing > Destination; Click New; Network Address / Netmask: 172.16.10.0 / 255.255.255.0; Click Gateway; Interface: tunnel.1; Click OK

May 06, 2012 · See the full on-line class at: http://puluka.com/classes/course/view.php?id=5 Route-Based VPN Concepts & Terminology Configuring VPNs Verifying Operations I am using the policy-based VPN solution on the Cisco router and not the virtual tunnel interface (VTI) approach. That is: No route is needed on the router while the Proxy IDs must be set on the Juniper firewall. (However, I also documented the route-based VPN solution between a ScreenOS firewall and a Cisco router here.) Pureport, MultiCloud, Private Connectivity, Private Cloud Connectivity, Multicloud in Minutes, VPN, IPSEC VPN, Configuration Guide, Juniper Netscreen, Route-Based, Static, VPN This configuration guide includes information needed to connect a Juniper Netscreen (SSG, ISG) firewall to the Pureport platform via a routed IPSEC VPN using BGP for routing. If you have a policy-based VPN, the source and destination address in the policy will determine what proxy IDs NetScreen will use. They must match with what is being proposed. If it's a routing-based VPN, you can specify the proxy IDs in the advanced page of the AutoIKE configuration. Virtual Tunnel Interface (VTI) support for ASA VPN module. The ASA VPN module is enhanced with a new logical interface called Virtual Tunnel Interface (VTI), used to represent a VPN tunnel to a peer. This supports route based VPN with IPsec profiles attached to each end of the tunnel.

Route-Based VPN As the name implies a route-based VPN is a connection in which a routing table entry decides whether to route specific IP connections (based on its destination address) into a VPN tunnel or not. This routing statement is placed in the routing table of the firewall/router such as any other static/dynamic/connected routes.

Below shows the network topology that our example is based upon. Netscreen. Below shows the Juniper Netscreen configuration steps. The configuration is pretty standard. However one interesting point is the way in which a route based VPN with an interface based MIP is used. May 06, 2012 · See the full on-line class at: http://puluka.com/classes/course/view.php?id=5 Route-Based VPN Concepts & Terminology Configuring VPNs Verifying Operations I am using the policy-based VPN solution on the Cisco router and not the virtual tunnel interface (VTI) approach. That is: No route is needed on the router while the Proxy IDs must be set on the Juniper firewall. (However, I also documented the route-based VPN solution between a ScreenOS firewall and a Cisco router here.) Pureport, MultiCloud, Private Connectivity, Private Cloud Connectivity, Multicloud in Minutes, VPN, IPSEC VPN, Configuration Guide, Juniper Netscreen, Route-Based, Static, VPN This configuration guide includes information needed to connect a Juniper Netscreen (SSG, ISG) firewall to the Pureport platform via a routed IPSEC VPN using BGP for routing.

The section below which is highlighted in bold shows the status of the vpn tunnel (left) and the status of the VPN monitor (right). In this case the VPN tunnel is active and the VPN monitor is dashed out as it isnt enabled. netscreen(M)-> get sa | i [peer ip] 00000007< [peer ip] 500 esp:3des/md5 zbcA14zz 3317 unlim A/- 22 0

Apr 28, 2013 · Tutorial IPSec Site to Site VPN between Juniper Netscreen firewalls fleszvideos. Configuring Route-Based Site-to-Site IPSec VPN on the SRX Virtual Private Networking - Duration: The articles listed below will help you get started with configuring your Juniper ScreenOS Firewall device with a Route Based LAN-to-LAN VPN. (For an explanation of Route-based VPNs vs. Policy-based VPNs, refer to KB4124). SRX Series,vSRX. Understanding Policy-Based IPsec VPNs, Example: Configuring a Policy-Based VPN Apr 15, 2014 · The Configuring Route-Based Site-to-Site IPsec VPN on the SRX Series Learning Byte discusses the configuration of a secure VPN tunnel between two Juniper Networks SRX-series devices. May 10, 2010 · Netscreen Remote Dial-UP VPN with AD Radius Authentication and route based VPN / tunnel interface The following procedure explains how to set up a Juniper ScreenOS based firewall to accept Netscreen Remote Client VPN connections and authenticate users using Active Directory (Radius via Windows 2003 IAS or Windows 2008 NPS).